Electro - Pneumatic Trainer with Work Station

Product Description

ME 7644 - Electro -Pneumatic Trainer with Work Station

Technical Specification:

Pneumatic Components

- Pneumatic Cylinder (Foot mounting)

- Single acting cylinder: Max. Stroke length 100mm,(1 No.)Bore dia:25 mm

- Double acting cylinder: Max. Stroke length 100 mm,(1 No.) Bore dia:25 mm

- Different type of valve

- Non-return valve: 1/4 inch connection

- One-way flow control valve: 1/4 inch, Square body

- 3/2 Way single solenoid valve: With LED (1No.)

- 5/2 Way single solenoid valve: With manual override and LED (1No.)

- 5/2 Way double solenoid valve: With manual override and LED (1No.)

- A.F.R / F.R.L unit:  0-10Kg/cm2, 1/4 inch connection

(Pressure regulator and water spectator)

- 5/2 hand lever valve:  Withmanually-operated switch (1No.)

- 6 Way block manifold:  Selfclosing with NVR

- Shuttle valve (OR) (1No.)

- Two-pressure valve (AND) (1No.)         

- 3/2 Way valve                 :Manually-actuated normally closed (2 Nos.)

- 3/2 Way valve                 :Pneumatically-actuated spring return (1No.)

- 3/2 Way valve                 :Roller lever direct-actuated normally closed

 (2Nos.)

- 5/2 Way valve                 :With manually-operated switch (1No.)

- 5/2 Way valve                 :Pneumatic-actuated spring return (1 No.)

- 5/2 Way valve                 :Pneumatic-actuated double pilot (1No.)

- Proximity sensors: Diameter: 18, Sensing distance: 5

- Pressure gauge: Dial size: 100, connection 1/2 inch BSP Capacity:7 Kg/cm2

- Pneumatic Motors: Unidirectional motor (Free speed)

 Air pressure (psi) 90, RPM:22000            

- Standard Accessories

- Quick Push-Pull connectors

- Plastic tub

- Quick connectors: Pressure gauge 16 bar

- Male connectors: 1/4 inch connection

Profile plate, anodized                  : 1100x700 mm, with carriers,mounting aluminum frames and mounting accessories (To be fitted onto thepneumatic workstation) Compressor unit

- Suitable for pressure   :8Kg/cm2

- Discharge: 2 cfm (56 lpm)

- Reservoir capacity: 25 Liters (or more), 230V, 50 Hz, withpressure regulator and water separator

Pneumatic WorkstationTable

Pneumatic workstationwith 45 square mm aluminum profile legs, wooden work surface, and one pedestaldrawer unit having 5 drawers, each with handles and individual locks, onmetallic full panel drawer slide:

-  Work table size: 1200mm(L) x 900mm(W) x900mm(H), with four castor wheels including two lockable wheels at the frontside,

- Drawer size (approx.):                460mm(L) x 495mm(W) x 158mm(H)each, and overall size of drawer unit (Approx.) 470mm(L) x 495mm(W) x 825mm(H)

- Drawer slide height      : 85mm Carrier for mounting components,such as PB & relay boxes.

- Carrier: Anodizedaluminum profile plate as a carrier for PB & Relay Box

- Electronic ControllerModule:  8051 CPU Memory 64kB Flash Selectionfor Auto / Manual operation through toggle switches System control manuallythrough Push to ON switches Reset button for micro controller

Power requirement:220VAC +10%, 50Hz

- Pushbutton stationfor: With 3 illuminated momentary contact Electrical signal input Switches (1NO + 1 NC) and 1 illuminated maintained contact switch (1 NO+1 NC), contactload 2A Indicating lamp: 24 VDC Operated

- Relay station:  With 3 relays’ each with 4 contact sets(3NO+1NC or change-over type), 5 A

- Power supply unit:Input voltage: 85~265 V AC, 50Hz

Output voltage          : 24 V DC

Output current          : max. 4.5A

Short-circuit proof